HomePlumbing ServicesTankless Water Heaters

Tankless water heaters in Lone Oak, TX and nearby

Tankless Water Heater Installation and Repair

A tankless water heater gives you hot water that doesn't run out, but only if it's sized and installed right. On The Way Plumbing does tankless water heater installation, repair and maintenance for homes and businesses around Lone Oak, Hunt County and Rains County. We'll tell you straight whether tankless makes sense for your house before you spend the money.

(903) 458-4026

  • 5.0 on Google from 354 reviews
  • Texas license M-44817
  • Family owned in Lone Oak, TX
  • Free estimates, upfront pricing
  • Emergency plumbers on call 24/7

How a tankless water heater works

A tank water heater keeps 40 or 50 gallons hot all day whether you use it or not. A tankless unit works on demand. When you open a hot tap, a flow sensor notices the water moving and fires the burner (or the elements, on an electric model). The water runs through a heat exchanger and comes out hot. Close the tap and it shuts back down.

That's where the endless hot water comes from. As long as the heater can keep up with the flow, it keeps heating. The catch is that word: keep up. Every tankless unit is rated in gallons per minute, and how many gallons it can deliver depends on how much it has to raise the temperature. Cold winter water coming in means it has to work harder, so it can deliver less flow at the same output temperature.

That's why sizing matters so much more on tankless than on a tank. A tank that's a little small runs out sooner. A tankless unit that's too small gives you lukewarm showers when someone starts the dishwasher.

Tankless vs. tank water heater

Tankless isn't the right call for every house. Here's how tankless vs. tank stacks up, pros and cons on both sides. If a regular tank still fits your needs, our water heater installation and repair page covers those.

Tankless water heaterTank water heater
Hot water supplyEndless, up to its flow ratingRuns out when the tank is used up
Upfront costHigher. The unit and install both cost moreLower
Operating costNo standby heat loss, since it only heats what you useKeeps a full tank hot around the clock
Wall spaceMounts on a wall, frees up a closet or garage cornerNeeds floor space for the tank
LifespanUsually longer, with regular flushingCommonly around 8 to 12 years
MaintenanceNeeds a descaling flush, more often with hard waterOccasional flush and anode rod check
Install needsOften a bigger gas line, new venting or heavy electricalUsually a like-for-like swap

Tankless water heater installation: what goes into it

A good tankless water heater installation starts with a few questions about your house before anybody picks a unit. Most of the problems people have with tankless heaters trace back to the install, not the heater.

Sizing by flow and temperature rise

We add up the fixtures you'd realistically run at the same time: two showers and the kitchen sink, a shower and the washing machine, a big tub. That gives a flow target in gallons per minute. Then we look at temperature rise, which is the difference between your incoming water temperature and the temperature you want at the tap. The bigger the rise, the bigger the heater needs to be for the same flow. Some bigger homes do best with two units.

Gas line size

A gas tankless water heater installation often needs more gas than the old tank heater used. A tank burner might be a small fraction of what a whole house tankless unit pulls at full fire. If the gas line size is too small, the heater starves when it needs the most gas, and you get error codes or cold water. We check the meter, the pipe size and the length of the run, and upsize the line if needed. Our gas line installation and repair page has more on that work.

Venting and condensate

Gas tankless heaters can't use the old water heater flue in most cases. They need venting made for that unit. High efficiency models also make condensate, so they need a condensate drain line. Where the heater goes (garage wall, outside wall, utility closet) depends a lot on where the venting can run.

Isolation valves for easy flushing

We install isolation valves on the water connections. They let you or us shut off the heater and hook up a pump to flush it without draining the house plumbing. If your current tankless doesn't have them, flushing is a much bigger job, and that's usually why it never gets done.

Electric tankless units

An electric tankless water heater for a whole house needs large dedicated circuits, and many older electrical panels can't handle it without an upgrade. Smaller electric units work well for a single sink or a far bathroom. We'll tell you up front if your panel is the limit so you can plan around it.

Our tankless installation process

From the first call to your first hot shower, here's how it goes.

Tell us about your house

Call or text (903) 458-4026. Tell us how many bathrooms you have, how many people live there, what fuel your current heater uses, and where it sits. A photo of the old heater and your gas meter helps.

Site visit and sizing

We look at the gas line, the venting route, the electrical if it's an electric unit, and the water connections. Then we size the heater for your real peak use.

Upfront quote with options

You get an upfront quote that spells out the unit, the gas line work, the venting and anything else the job needs, so there are no surprises. Estimates are free, and financing is available.

Install day

We shut off the water and fuel, remove the old tank and haul it off, mount the new unit, run the gas, venting and water lines, and install isolation valves. Austin F. went 24 hours from a dead water heater to a new tankless install.

Test and walkthrough

We leak test the gas connections, fire the unit, test the flow at several fixtures and set the temperature. Then we show you the controls and what the maintenance looks like.

Tankless water heater repair

Tankless units are reliable when they're maintained, but when they act up, the symptoms can be confusing. Our tankless water heater repair starts with the error code, then we test the parts behind it. Here's what the common problems usually mean.

Error code on the display

Most tankless heaters show an error code when something's off. The code points to a system (ignition, flow, overheating, venting), not always the exact part. Write it down or text us a photo of the display before you reset it. That saves time on the diagnosis.

Water not getting hot

A tankless water heater not getting hot can be a gas supply problem (line too small or a valve partly closed), an ignition problem, a dirty flame rod, or flow too low to trigger the burner. A clogged inlet filter screen or scale buildup in the heat exchanger shows up this way too.

Hot, then cold, then hot

A short burst of cold water between hot is called a cold water sandwich. Some of it is normal when you turn the tap off and back on fast. If it's bad or new, it can mean a problem with the flow sensor or the heater cycling on low flow.

Won't fire at a single faucet

Every tankless heater has a minimum flow rate it needs to turn on. A low flow faucet or a partly clogged aerator might not move enough water to trigger it. Sometimes the fix is at the faucet, not the heater.

Hot water fades during long showers

If hot water gets weaker partway through, the heater may be undersized, short on gas, or choked with scale. Scale buildup makes the heat exchanger overheat and the unit backs itself down to protect itself.

Tankless water heater maintenance

The one maintenance job a tankless heater really needs is a descaling flush. Water running through the heat exchanger leaves minerals behind, and hard water leaves a lot of them. That scale cuts efficiency, sets off error codes and wears the heater out early.

A tankless water heater flush goes like this: we shut off the gas or power and close the isolation valves, hook a small pump and hoses to the service ports, and circulate a descaling solution through the heat exchanger for a while. Then we flush it with clean water, clean the inlet filter screen, open everything back up and test it.

  • How often: about once a year for most homes. With hard water, more often. If you have a water softener, you can usually go longer.
  • Inlet filter: clean it during each flush, or any time you notice reduced flow.
  • Venting and air intake: keep them clear of debris, nests and anything stacked against the unit.

If scale is an ongoing fight, a water softener protects the tankless heater along with every other fixture in the house.

Tankless customers in their own words

★★★★★

"Blake was great! He helped me fully understand my tankless water heater..."

Madison M. · Google review

★★★★★

"24 hours turnaround time from a dead water heater to a new tankless install."

Austin F. · Google review

Tankless service across Hunt and Rains County

We install and service tankless water heaters from our home base in Lone Oak out about 60 miles, covering Hunt County, Rains County and nearby towns in Hopkins, Wood and Rockwall counties. Greenville homeowners can also check our page on water heater repair in Greenville, TX. If your town isn't listed, call and ask.

Common questions

Thinking about tankless?

Call or text (903) 458-4026 with a photo of your current water heater and gas meter. We'll tell you what a tankless install at your house would take and give you a free estimate.